固原僬厍商贸有限公司

您好,歡迎光臨萊州聚峰機械有限公司網站!

服務熱線

400-879-1999

行業資訊

小型混凝土攪拌車輪胎更換的步驟

來源:http://www.apstzs.com/ 時間:2023-04-26

小型混凝土攪拌車如何更換輪胎?下面跟隨小型混凝土攪拌車廠家一起來了解一下吧。
How to change the tires of a small concrete mixer truck? Let's follow the manufacturers of small concrete mixer trucks to learn more.
1、啟動機器,近尋找一塊比較平坦開闊的場地,壓下動臂升降桿,利用動臂支承使前輪離地,然后用支架支撐在閃橋靠近爆胎的一側,并將后輪楔好(必須與駕駛員密切配合,以免造成人身傷害)。
1. Start the machine, search for a relatively flat and open area, press down on the boom lifting rod, use the boom support to lift the front wheels off the ground, and then use a bracket to support the side of the flash bridge near the tire burst, and wedge the rear wheels (close cooperation with the driver is necessary to avoid personal injury).
2、利用撬杠等等工具,拆卸擋圈及鎖圈然后檢查輪胎襯墊與輪輞外表面是否粘連(輪胎使用時間較長,襯墊與輪輞外表面可發生粘連)。若發生可撤掉支撐物,使機器在短距離內慢速往復運行,直襯墊與輪輞外表面脫離;嚴禁轉向和高速行駛,以免損壞內胎。然后,前輪重新支撐起來。
2. Use pry bars and other tools to remove the retaining ring and lock ring, and then check if the tire pad adheres to the outer surface of the rim (if the tire is used for a long time, the pad may adhere to the outer surface of the rim). If there is a problem, the support can be removed, allowing the machine to run slowly back and forth over a short distance until the pad detaches from the outer surface of the wheel rim; It is strictly prohibited to turn and drive at high speeds to avoid damaging the inner tube. Then, the front wheels are supported again.
3、將內、外胎的相對位置作好標記,以便查找、異物和修補輪胎。
3. Mark the relative positions of the inner and outer tires for easy identification, removal of foreign objects, and tire repair.
4、利用撬杠等工具,將輪胎從輪輞上拆下。注意,動作要輕柔配合要默契,避免被輪胎砸傷,并且要保護好氣門嘴。
4. Use tools such as a pry bar to remove the tire from the rim. Attention, the movements should be gentle and harmonious, to avoid being hit by tires, and to protect the valve mouth.
5、外胎被釘子等細長異物扎傷后,若表面無明顯創(chuàng )口或創(chuàng )口較小,則此外胎可繼續使用(因為小型混凝土攪拌車輪胎屬低壓胎,且運行速度比較慢);若創(chuàng )口較大,則必須進行修補(因為機器運行時,輪胎受擠壓磨擦,時間一長會(huì )損壞內胎,甚創(chuàng )口越來越大、內胎突出,造成輪胎報廢)。
5. After the outer tire is punctured by slender foreign objects such as nails, if there is no obvious wound on the surface or if the wound is small, the outer tire can continue to be used (because the small concrete mixer tire is a low-pressure tire and the running speed is relatively slow); If the wound is large, it must be repaired (because during machine operation, the tire is compressed and rubbed, which can damage the inner tube over time, and even cause the wound to become larger and the inner tube to protrude, causing the tire to be scrapped).
6、若是新內胎,必須將氣門嘴底部的螺栓擰緊,以防漏氣;然后將外胎內腔的異物,并撒入適當的滑石粉,涂抹均勻。為了使襯墊與內、外胎貼緊,在裝入內胎后應給內胎適當充氣,再塞入襯墊。
6. If it is a new inner tube, the bolts at the bottom of the valve must be tightened to prevent air leakage; Then remove any foreign objects from the inner cavity of the outer tire, sprinkle appropriate talcum powder, and apply evenly. In order to make the liner tightly adhere to the inner and outer tires, the inner tire should be appropriately inflated after being installed, and then the liner should be inserted.
小型混凝土攪拌車
7、將輪胎裝到輪輞上,裝上鎖圈、擋圈;安裝過程中要保護好氣門嘴。
7. Install the tire onto the rim and install the lock ring and retaining ring; During the installation process, it is necessary to protect the gas valve mouth.
8、用車載空壓機給輪胎充氣。
8. Use a car mounted air compressor to inflate the tires.
9、壓下動臂升降桿,取出支架;此換胎完畢,整個過程大約需要50min。更換后輪胎時,則需要另一臺小型混凝土攪拌車或者其他起重設備輔助,將后輪胎支撐起來,其他程序則與更換前輪胎相同。
9. Press down the boom lifting rod and take out the bracket; At this point, the tire change is complete, and the entire process takes approximately 50 minutes. When replacing the rear tire, another small concrete mixer truck or other lifting equipment is needed to support the rear tire, and the other procedures are the same as before replacing the front tire.
以上是為您總結的有關小型混凝土攪拌車輪胎更換的小知識,希望對您有所幫助,有任何問題隨時聯系我們,關注我們官網http://www.apstzs.com,我們會(huì )定期更新有關小型混凝土攪拌車的小知識。
The above is a summary of some knowledge about tire replacement for small concrete mixer trucks. We hope it can be helpful to you. If you have any questions, please feel free to contact us and follow our official website http://www.apstzs.com We will regularly update our knowledge about small concrete mixer trucks.
上一篇:全自動攪拌車需要及時更換幾個相關部件!
下一篇:
tag:混凝土攪拌車,小型混凝土攪拌車,全自動混凝土攪拌車

小型混凝土攪拌車輪胎更換的步驟

作者:中科聚峰混凝土攪拌車廠家 時間:2023-04-26

小型混凝土攪拌車如何更換輪胎?下面跟隨小型混凝土攪拌車廠家一起來了解一下吧。
How to change the tires of a small concrete mixer truck? Let's follow the manufacturers of small concrete mixer trucks to learn more.
1、啟動機器,近尋找一塊比較平坦開闊的場地,壓下動臂升降桿,利用動臂支承使前輪離地,然后用支架支撐在閃橋靠近爆胎的一側,并將后輪楔好(必須與駕駛員密切配合,以免造成人身傷害)。
1. Start the machine, search for a relatively flat and open area, press down on the boom lifting rod, use the boom support to lift the front wheels off the ground, and then use a bracket to support the side of the flash bridge near the tire burst, and wedge the rear wheels (close cooperation with the driver is necessary to avoid personal injury).
2、利用撬杠等等工具,拆卸擋圈及鎖圈然后檢查輪胎襯墊與輪輞外表面是否粘連(輪胎使用時間較長,襯墊與輪輞外表面可發生粘連)。若發生可撤掉支撐物,使機器在短距離內慢速往復運行,直襯墊與輪輞外表面脫離;嚴禁轉向和高速行駛,以免損壞內胎。然后,前輪重新支撐起來。
2. Use pry bars and other tools to remove the retaining ring and lock ring, and then check if the tire pad adheres to the outer surface of the rim (if the tire is used for a long time, the pad may adhere to the outer surface of the rim). If there is a problem, the support can be removed, allowing the machine to run slowly back and forth over a short distance until the pad detaches from the outer surface of the wheel rim; It is strictly prohibited to turn and drive at high speeds to avoid damaging the inner tube. Then, the front wheels are supported again.
3、將內、外胎的相對位置作好標記,以便查找、異物和修補輪胎。
3. Mark the relative positions of the inner and outer tires for easy identification, removal of foreign objects, and tire repair.
4、利用撬杠等工具,將輪胎從輪輞上拆下。注意,動作要輕柔配合要默契,避免被輪胎砸傷,并且要保護好氣門嘴。
4. Use tools such as a pry bar to remove the tire from the rim. Attention, the movements should be gentle and harmonious, to avoid being hit by tires, and to protect the valve mouth.
5、外胎被釘子等細長異物扎傷后,若表面無明顯創(chuàng )口或創(chuàng )口較小,則此外胎可繼續使用(因為小型混凝土攪拌車輪胎屬低壓胎,且運行速度比較慢);若創(chuàng )口較大,則必須進行修補(因為機器運行時,輪胎受擠壓磨擦,時間一長會(huì )損壞內胎,甚創(chuàng )口越來越大、內胎突出,造成輪胎報廢)。
5. After the outer tire is punctured by slender foreign objects such as nails, if there is no obvious wound on the surface or if the wound is small, the outer tire can continue to be used (because the small concrete mixer tire is a low-pressure tire and the running speed is relatively slow); If the wound is large, it must be repaired (because during machine operation, the tire is compressed and rubbed, which can damage the inner tube over time, and even cause the wound to become larger and the inner tube to protrude, causing the tire to be scrapped).
6、若是新內胎,必須將氣門嘴底部的螺栓擰緊,以防漏氣;然后將外胎內腔的異物,并撒入適當的滑石粉,涂抹均勻。為了使襯墊與內、外胎貼緊,在裝入內胎后應給內胎適當充氣,再塞入襯墊。
6. If it is a new inner tube, the bolts at the bottom of the valve must be tightened to prevent air leakage; Then remove any foreign objects from the inner cavity of the outer tire, sprinkle appropriate talcum powder, and apply evenly. In order to make the liner tightly adhere to the inner and outer tires, the inner tire should be appropriately inflated after being installed, and then the liner should be inserted.
小型混凝土攪拌車
7、將輪胎裝到輪輞上,裝上鎖圈、擋圈;安裝過程中要保護好氣門嘴。
7. Install the tire onto the rim and install the lock ring and retaining ring; During the installation process, it is necessary to protect the gas valve mouth.
8、用車載空壓機給輪胎充氣。
8. Use a car mounted air compressor to inflate the tires.
9、壓下動臂升降桿,取出支架;此換胎完畢,整個過程大約需要50min。更換后輪胎時,則需要另一臺小型混凝土攪拌車或者其他起重設備輔助,將后輪胎支撐起來,其他程序則與更換前輪胎相同。
9. Press down the boom lifting rod and take out the bracket; At this point, the tire change is complete, and the entire process takes approximately 50 minutes. When replacing the rear tire, another small concrete mixer truck or other lifting equipment is needed to support the rear tire, and the other procedures are the same as before replacing the front tire.
以上是為您總結的有關小型混凝土攪拌車輪胎更換的小知識,希望對您有所幫助,有任何問題隨時聯系我們,關注我們官網http://www.apstzs.com,我們會(huì )定期更新有關小型混凝土攪拌車的小知識。
The above is a summary of some knowledge about tire replacement for small concrete mixer trucks. We hope it can be helpful to you. If you have any questions, please feel free to contact us and follow our official website http://www.apstzs.com We will regularly update our knowledge about small concrete mixer trucks.

截屏,微信識別二維碼

足球看盘软件哪个好| 球宴app官方入口| 哪个app可以直播英超比赛| 球宴app官方入口| jrs低调看NBA高清直播官网| 免费看球直播软件| jrs低调看高清直播免费| 咪咕cctv5现场直播| nba直播(jrs无插件)| 使用这些app的好处| 球天下体育app下载| 咪咕咪咕体育| 178足球免费直播手机版下载| 这些app功能齐全| jrs直播 极速体育| 178足球直播视频| 看足球直播软件| 人人体育ios版本| jrs低调看高清直播NBA无插件| 雨燕体育直播| 斗球体育直播app下载| 免费看球直播软件| 免费看足球比赛app| 奥运女足2024赛程表格| 足球体育平台app| JRS低调看球免费高清视频直播| 免费看足球比赛app| 蓝鲸体育app官方下载| 手机足球直播app| 实况足球网易版官网最新版本| 咪咕体育免费直播手机app| 88体育app官网下载| 十大免费体育直播软件| 足球比赛app官网| 使用这些app的好处| 人人体育安卓版下载| JRS低调看球免费高清视频直播| 咪咕cctv5现场直播| 蓝鲸体育直播app官网下载| 篮球官方直播| 咪咕cctv5现场直播|