When we check the concrete mixing plant regularly, we need to check the steel wire rope first. Put a little butter on it for a week to ensure adequate operation. If the steel wire rope is seriously worn, it shall be replaced in time. Check the grease level of the heavy oil pump and replace the grease if necessary. In addition, the water supply system of the concrete mixing plant shall be kept clean at all times to avoid blockage. The suction valve shall be inspected and cleaned regularly.
每個電機和電氣組件的接線不得松動，并且應檢查交流接觸器的接觸器。 混凝土攪拌站配電箱中的灰塵應清理干凈，限位開關不得進入水中。 經常檢查設備，可以隨時發現設備的使用故障，應及時對混凝土攪拌站進行維修和修理，以延長其使用壽命。
The wiring of each motor and electrical component shall not be loose, and the contactor of AC contactor shall be checked. The dust in the distribution box of the concrete mixing plant shall be cleaned, and the limit switch shall not enter the water. Check the equipment frequently, and the use failure of the equipment can be found at any time. The concrete mixing plant shall be repaired and repaired in time to prolong its service life.
，氣體控制系統可以實現便捷的輸入，便捷的操作，并且可以準確地調整和修改每種物料的設定值; 電氣控制系統須具有完善的自鎖和互鎖功能，以確保系統準確，可靠地運行。 常見的故障電氣控制系統須具有故障檢測和報警功能。 使用混凝土攪拌
Firstly, the gas control system can realize convenient input and convenient operation, and can accurately adjust and modify the set value of each material; The electrical control system must have perfect self-locking and interlocking functions to ensure the accurate and reliable operation of the system. The common fault electrical control system must have the function of fault detection and alarm. Mixing with concrete
其次，該空氣控制系統在混凝土攪拌站的配料過程中輸出為零，從而地控制了計量精度的功能，并設有光報警裝置。 有些用戶甚不知道空氣控制系統的一部分，這并不重要。 實際上，空氣控制系統就是要實現整套設備的自動化。 沒有空氣控制系統的混凝土攪拌站設備不能正常運行，其重要性很高。
Secondly, the output of the air control system is zero in the batching process of the concrete mixing plant, so as to effectively control the function of measurement accuracy, and a light alarm device is set. Some users don't even know part of the air control system, which is not important. In fact, the air control system is to realize the automation of the whole set of equipment. The equipment of concrete mixing plant without air control system can not operate normally, which is of high importance.
空氣控制系統在混凝土攪拌站中的重要性不言而喻。
The importance of air control system in concrete mixing plant is self-evident.
實際上，整個混凝土攪拌站的攪拌系統，骨料系統，輸送系統，氣體控制系統和控制系統都是重要和必不可少的。 混凝土攪拌站生產線中的中間攪拌倉主要是由于骨料的混合效率有時高于粉末和水的混合效率，因此過渡室用于等待粉末和水的配料工作。 常見于大型攪拌站。
In fact, the mixing system, aggregate system, conveying system, gas control system and control system of the whole concrete mixing plant are important and essential. The intermediate mixing bin in the production line of concrete mixing plant is mainly because the mixing efficiency of aggregate is sometimes higher than that of powder and water, so the transition chamber is used to wait for the mixing of powder and water. Common in large mixing plants.
如果小型攪拌站使用料斗升降機，則實際上沒有中間皮帶倉，骨料可以在提升的料斗中等待。 同時，由于骨料沉重而容易忘記的部分將沉入底部。 此時，如果加入骨料，則不利于混凝土的均勻混合。 它將延長混合周期并降低混合效率。 此時，將粉末放入水中。 實際上，與骨料混合并攪拌，提高混合效率是有益的。
If a hopper elevator is used in a small mixing plant, there is actually no intermediate belt bin, and the aggregate can wait in the lifted hopper. At the same time, the easily forgotten part due to the heavy aggregate will sink to the bottom. At this time, if aggregate is added first, it is not conducive to the uniform mixing of concrete. It will extend the mixing cycle and reduce the mixing efficiency. At this time, first put the powder into water. In fact, it is beneficial to mix and mix with aggregate to improve mixing efficiency.
如果需要維護，則電動機要連續運行，并且日常維護非常重要：電動機在工作時，請注意工作環境，不要太顛簸，以防止電動機損壞或減速。 使用壽命。 還要檢查外觀，風扇是否正常工作，是否異常振動，聯軸器是否可靠，基座是否定期固定，軸承是否正常工作(聽聲音)以及溫度是否正常( 紅外溫度計))，電流是否正常(鉗型電流表)，并且纏繞的電動機還須檢查碳刷和滑環。 如果一方面存在異常，則需要快速進行電機維修和處理。 否則，情況嚴重后，您將無法處理。。
The motor shall not be damaged during daily operation or continuous maintenance. If it is necessary to slow down the motor, please pay attention to prevent the motor from being damaged. service life. Also check the appearance, whether the fan works normally, whether it vibrates abnormally, whether the coupling is reliable, whether the base is fixed regularly, whether the bearing works normally (listen to the sound) and whether the temperature is normal (infrared thermometer)), whether the current is normal (clamp on ammeter), and check the carbon brush and slip ring of the wound motor. If there are abnormalities on the one hand, the motor needs to be repaired and handled quickly. Otherwise, when the situation is serious, you will not be able to handle it..
